Stainless Steel Strip & Stainless Slit Coil
Stainless Steel Slit Coil and Slit Strip products are avalable in a wide variety of alloys and sizes that serve many applications and markets. Our alloys and sizes include but, are not limited to:
- 201, 301, 302, 304, 304, 316, 316Ti, 316L, 17-7Ph, 420
- Other Alloys Available Upon Request
- Gauges From: 0.0015”- .062” / 0.0381mm – 1.57mm
- Widths From: 0.024” – 24” / 0.6096mm – 609.6mm
- Round, Safety, Broken Corner, and Square Edging Available
- Wide Variety of Spool/Winding Options Including Ribbon Wound or, Oscillate Reels and Spools,
- Exceptionally Close Precision Slit Tolerances
- Supplying Automotive, Electronics, Oil & Gas, Aerospace, Medical, Fastener, Springs, Commercial, Power Generation, and More
- 60+ Years of Strip Innovation, Service, & Expertise
- Strip Available From 7 Locations in the U.S., Mexico, and Canada
301 stainless strip, ASTM-A-666, is slightly lower in chromium and nickel content than Type 302. The lower nickel content causes Type 301 to work harden more rapidly and retain greater ductility than the same temper of Type 302. Gibbs stocks 301 Stainless Strip in gauges from 0.0022″ to 0.050″ precision slit to widths from 0.022 to 12″. Type 301 is available in a variety of tempers. Learn More
301 High Yield or Extra Full Hard, ASTMA-666, issued for special applications requiring extra high strength and hardness. This extra high strength material has a minimum tensile strength of 270,000 PSI. Gibbs stocks 301 High Yield Strip in gauges from 0.002″ to 0.032″ precision slit to widths from 0.022″. Type 301 High Yield is sold to AMS5519 – Chemical properties only. View Gauges
302 Stainless Steel Strip, ASTMA-666, a general purpose stainless alloy, is 18% chromium and 8% nickel. It possesses excellent resistance to heat and corrosion. Type 302 cannot be hardened by heat treatment and is slightly magnetic after cold working. It welds easily. Gibbs stocks Type 302 Stainless in gauges from .003 to .030 precision slit to widths from .022″ to 12″. View Gauges
304 stainless steel strip and slit to width coil, ASTMA-666, is similar to Type 302, but has a maximum carbon content of 0.08%. This material has an excellent combination of corrosion resistance and formability. Gibbs stocks Type 304 annealed stainless in gauges from 0.0053″ to 0.062″ and T304 tempered in gauges from .002″-.025″.
305 is used for applications requiring a low rate of work hardening and typically undergoes severe cold forming during fabrication. The higher nickel content slows the work hardening and makes it ideal for eyelet and other deep draw applications. Gibbs can supply Type 305 Eyelet Quality in gauges from 0.005″ – 0.025″ in the deep draw annealed condition.
316, ASTMA-666 stainless steel strip are molydbenum bearing stainless steels possessing a greatly increased resistance to chemical attack as compared to that of the basic chromium-nickel analysis. In addition, Type 316 also offers higher creep, stress-to-rupture, and tensile strengths at elevated temperatures than any other stainless steel. Gibbs stocks this material in gauges from 0.005″ – 0.025″ in the annealed and 1/4 hard conditions
316Ti™, is a titanium stabilized version of Type 316 stainless. It is produced to ASTM A240 and DIN/EN No. 1.4571. Titanium is added to minimize corrosion over extended exposure to elevated temperatures ranging from 900 to 1500 degrees °F (425 to 815 °C). The alloy resists corrosion at higher temperatures because the addition of titanium stabilizes the structure against chromium precipitation. This alloy was developed to improve the performance of 316 and 316L at elevated temperatures. It is commonly used is flexible ducts and chimney liners
Type 17-7 PH, “Condition C” has the corrosion resistance of Type 302 plus superior strength and heat resistance. After forming, it can be heat treated at 900° F for one hour to achieve maximum “CH” tensiles. Gibbs stocks 17 chrome-7 nickel stainless steel in the “C” cold rolled condition in gauges from .008″ to .025″.